Citation: Ying Gang LUO,  Bo Gang LI,  Guo Lin ZHANG. A New Quinolizidine Alkaloid from Boehmeria siamensis[J]. Chinese Chemical Letters, ;2001, 12(4): 337-338. shu

A New Quinolizidine Alkaloid from Boehmeria siamensis

  • Received Date: 4 September 2000

  • A new quinolizidine alkaloid, 3-(4-hydroxyphenyl)-4-(3-methoxy-4-hydroxyphenyl)-3, 4-dehydroquinolizidine (1), was isolated from the ethanol extract of the whole plants of Boehmeria siamensis Craib. Its structure was elucidated on the analysis of 1D NMR and 2D NMR spectrum.
  • The ever-flourishing electric vehicles, portable electronic devices and stationary energy storage systems have attracted worldwide attention towards high energy– power density electrochemical storage devices [15]. Supercapacitors hold the advantages of high-power output capability, fast charge-discharge rate, and long-time cycling stability, showing tremendous potential in high-power designs [69]. Unfortunately, their practical applications have long been constrained by the relatively poor energy density (5–20 Wh/kg) [1012]. Theoretically, the energy density (E) of supercapacitors is determined by the operation voltage (V) and capacitance (C) according to the equation, E = 0.5CV2 [13,14]. That is, a high E can be obtained by increasing C or enlarging V. In this regard, ionic liquid (IL) electrolyte with wide voltage window (3.7–5 V) exhibits a prominent superiority compared to its aqueous electrolyte counterparts (about 1 V) [1517]. Besides, the peculiarities of low volatility and non-flammability also render IL effectively avoid the safety hazards caused by leakage and flame of conventional organic electrolyte [1820]. Nevertheless, their intrinsic high viscosity and large ionic size always lead to poor affinity to most carbon electrode materials with insufficient micropores structure (< 2 nm), thus resulting in sluggish ion diffusion kinetics and poor rate performance.

    The porous carbon materials dominant with mesoporous active sites can provide plenty of ion-available diffusion channel for efficient mass transport, and therefore are strongly favored [2128]. With that in mind, numerous advanced carbon electrode materials have been addressed and displayed excellent capacitance performance within IL electrolytes, including graphene, carbon nanofibers, carbon nanotube, carbon sphere, as well as active carbon with high mesoporous [2934]. Nonetheless, most of them are produced from fossil fuels or unreproducible materials, which definitely detrimental to the sustainable development of resources and environment.

    By virtue of the low-cost, renewability, and environmental benefits, many biomass materials have constantly been developed as potential precursors for porous carbon, such as carbohydrate, bagasse, lignin, and various primary biomasses [3539]. Among them, lignin and its derivatives with high carbon content (more than 60 wt%), caused by their unique aromatic structure on natural macromolecule polymers, are considered as one of the most promising candidates [4043]. In materials science, the high carbon content of biomass sources contributes to obtain bio-derived carbon materials with high C/O ratios, giving rise to the improved conductive characteristics. Additionally, there are many functional groups (such as hydroxyl, methoxyl, carboxyl groups) on lignin, which not only help to introduce self-doped heteroatoms into carbon materials for good interface wettability, but also promote the formation of strong interchain entanglement and intermolecular bonds with environment [4448]. Such interactions in turn offer emerging opportunities for effective preparation of porous carbon with controllable morphologies via advanced methods, such as template methods [4951]. However, lignin is a complex and highly branched biopolymer consisting mainly of methoxylated phenylpropanoid acid units, such as p-hydroxyphenyl, guaiacol and butyl groups, cross-linked by various ether and carbon-carbon bonds. This highly branched structure leads to derived porous carbon generally featured with unfavorable pore distribution (microporous-dominated) and low specific surface area (SSA), which cannot match well with the ILs and severely degrades the rate capability at high current densities [5254]. If the lignin-derived porous carbon can be built with controllable pore structure, the accelerated transfer kinetics and outstanding electrochemical performance can be therefore achieved.

    In this contribution, we constructed a lignin-derived porous carbon with tunable mesostructure via a facile template strategy, in which sodium lignosulphonate worked as the major carbon sources, gelatin as binding agent, NaNO3 as template and activator agent, respectively. In details, as shown in Fig. 1a, the sodium lignosulphonate, gelatin and NaNO3 were firstly mixed in the water solution. Due to the water-soluble of sodium lignosulphonate and gelatin polymers, they can be easily dissolved into hot water to form a homogeneous sol on the molecular level. Subsequently, the sol was transformed into a physical cross-linked hydrogel matrix after cooling via interchain entanglement and intermolecular forces, attributing from the abundant multifunctional groups on these polymers. When freezing drying of hydrogel above, the NaNO3 fillers could be simultaneously dispersed in aerogel scaffold as pore engineers for tuning porous structure. After carbonization, the advanced lignin-derived porous carbons were fabricated. Herein, the proper calcination temperature was identified to be 900 ℃ through preliminary experiments (Figs. S1–S3 in Supporting information). Finally, the as-obtained carbon materials, which denoted as LPC-X, X = 0.3, 0.4 and 0.5 (according to the weight ratio of NaNO3 to total), were featured with not only 3D interconnected framework, high mesopore ratio and large SSA for fast ion adsorption/desorption and facilitated mass transfer, but also suitable heteroatoms doping for good interfacial wettability and high electrochemical stability. All these features collectively rendered the LPC electrode with superior specific capacitance, high energy-power density as well as excellent cycling lifespan.

    Figure 1

    Figure 1.  (a) Schematic illustration for the synthesis of advanced lignin-derived porous carbons. (b) SEM image and corresponding EDS mappings of (c) C, (d) O and (e) N elements for LPC-0.5 sample.

    The morphologies of as-prepared LPC-X (X = 0.3, 0.4 and 0.5) were examined by scanning electron microscope (SEM). As shown in Fig. 1b and Fig. S4 (Supporting information), all samples displayed typical 3D interconnected framework homogeneously decorated with numerous of pores. For detailed observations, elemental mapping images of LPC-0.5 were conducted, which illustrated that the C, O and small amounts of N elements were distributed uniformly on the 3D porous carbon scaffolds (Figs. 1ce). Such a particular interconnected porous structure was beneficial to afford a continuous electron transfer pathway, short ion diffusion distance, and large contact area between electrode and electrolyte, thereby rendering the excellent electrochemical performance.

    The detailed textural properties of as-synthesized carbon materials were further evaluated by N2 adsorption-desorption measurements. As depicted in Fig. 2a, all LPC-Xs presented typical IV-type curves with steep adsorption regions at P/P0 < 0.1 and distinctive H3-type hysteresis loops between P/P0 = 0.45 and 0.9, indicative of the co-existence of micropores and mesopores [55,56]. Besides, the SSAs were also calculated as derived from Brunauer–Emmett–Teller theory, reaching to as large as 2176.6, 2407.6 and 2453.3 m2/g for LPC-0.3, LPC-0.4 and LPC-0.5 samples, respectively (Table S1 in Supporting information). According to the pore size distributions displayed in Fig. 2b, all samples exhibited both micropores and mesopores structure, among which the micropore centered at 0.5–2 nm and the mesopore distributed around 2–5 nm, further confirming the hierarchical porous structures of LPC-Xs. Such small-size mesopore contributed to high availability of adsorption/desorption sites and shorten pathways of electrolyte ions, especially for IL electrolytes. Fig. 2c quantitatively described the contributions of mesopores to surface areas and pore volumes for all LPC-X samples, which denoted as Smeso and Vmeso, respectively. It can be observed the mesopores could be tuned by increasing the dosage of NaNO3, as the evidenced by the monotonic increased Smeso and Vmeso from that of LPC-0.3 (738.4 m2/g, 0.611 cm3/g) to LPC-0.4 (1486.6 m2/g, 1.284 cm3/g), and then to LPC-0.5 (1955.5 m2/g, 1.734 cm3/g). Notably, all these values were much higher than that for the carbon material directly carbonization of lignin, successfully demonstrating the high mesopore properties of LPC-X samples (Fig. S5 in Supporting information). In addition, the rich mesoporisity was also reflected by the proportions of Smeso and Vmeso, defined as Smeso /SSA and Vmeso /Vtotal, shown in Fig. 2c, which indicated that the samples were all mesopore-dominated. Specifically, the Smeso/SSA and Vmeso/Vtotal of LPC-0.5 sample reached the highest ratio of 79.7 and 89.7%, respectively. Overall, these mesopore-dominated hierarchical porous structures with favorable pore size and high SSA efficiently assured highly accessible sites for ion adsorption/desorption and facile kinetics for mass diffusion within IL electrolytes.

    Figure 2

    Figure 2.  The texture properties and surface chemistry of as-synthesized LPC-X (X = 0.3, 0.4 and 0.5) materials. (a) N2 adsorption–desorption isotherms. (b) Pore size distribution curves. (c) The changes of Smeso, Vmeso, Smeso/SSA and Vmeso/Vtotal ratios for LPC-X samples. (d) Raman spectra. (e) XPS survey spectra. (f) The content variation of C, O and N elements for different materials.

    The Raman spectra of LPC-X (X = 0.3, 0.4 and 0.5) samples exhibited two typical broader peaks (Fig. 2d), corresponding to the well-documented G band (1580 cm−1) and D band (1350 cm−1), respectively. The intensity ratio of G band to D band (IG/ID) represented the graphitization degree of carbon materials. It can be observed that the IG/ID of LPC-0.3, LPC-0.4 and LPC-0.5 were 1.03, 1.01 and 0.995, respectively, indicating the relatively high texture ordering and graphitization degree of LPC-Xs. X-ray photoelectron spectroscopy (XPS) analyses were further conducted to investigate the surface chemistry of the obtained samples. The results in Fig. 2e clearly revealed the existence of C and O elements in all LPC samples. In addition, the contents of N elements for LPC-0.3, LPC-0.4 and LPC-0.5, respectively, were detected to be as low as 1.57, 1.89 and 0.55 at% (Table S2), and therefore made them difficult to be identified in the XPS survey spectra. The co-existence of C, O and N elements demonstrated in XPS results were well consistent with the EDS mapping observations aforementioned, further confirming the efficiency of NaNO3-template synthesis strategy toward LPC in our work. Noteworthily, the concentrations of C elements were increased from 93.6 at% to 96.3 at%, while decreased for the O and N elements as the NaNO3 increased (Fig. 2f). And the lowest O/N content of 2.96 at%/0.55 at% were detected on the LPC-0.5 samples. Actually, the presence of heteroatoms is regarded as a double-edged sword for the carbon electrode that paired with IL electrolytes [57]. On one hand, the doped heteroatoms could effectively improve the wettability between the electrode surface and electrolytes. On the other hand, excess heteroatoms would introduce unstable defects and functional groups on electrode materials, which can react with the electrolyte by undesired Faradaic processes, thus triggering the electrolyte decomposition and capacitance fade. Therefore, the relatively low content of O/N heteroatoms in LPC samples can effectively ensure the high electrochemical stability of IL electrolyte during cycling.

    The electrochemical performances of LPC-X (X = 0.3, 0.4 and 0.5) were assessed in two-electrode coin-cell configurations with EMIBF4 electrolyte. Fig. 3a displayed the cyclic voltammetry (CV) curves of the samples at 50 mV/s. Apparently, all the curves exhibited symmetrical rectangular shapes with very small distortion, revealing the ideal electric double layer behaviors. For comparison, the LPC-0.5 possessed the largest CV loop area as compared to other samples, indicative of the optimum capacitance properties arising from its high mesoporous structure, large SSA and favorable heteroatoms. Furthermore, the CV curves of LPC-0.5 were also measured at different scan rates, which illustrated the curves maintained the typical rectangular shapes even at 200 mV/s, successfully implying the high reversibility and excellent rate capability properties (Fig. 3b). The same phenomena were observed for other samples (Figs. S6 and S7 in Supporting information). Galvanostatic discharge-charge (GCD) curves of LPC-0.5 were recorded from 0.5 A/g to 50 A/g to further elucidate the high electrochemical performance (Figs. 3c and d). All curves displayed nearly linear and symmetrical triangle-like shapes with small IR drop, verifying the ideal capacitance performance of LPC-0.5. The specific capacitances of LPC-Xs calculated based on the GCD curves were plotted in Fig. 3e. It was observed that the three samples delivered very close initial capacitances of 161, 166 and 166 F/g at 0.5 A/g, respectively, for LPC-0.3, LPC-0.4 and LPC-0.5 materials, which should be resulted from their similar SSAs [58]. Notably, with the increase of current density to 50 A/g, the LPC-0.5 still possessed a high capacitance retention of 82.5% as compared to LPC-0.3 (72.2% retention) and LPC-0.4 (77.1% retention) samples, further demonstrating the excellent rate capability of the LPC-0.5 sample. Even at a high mass loading of 8 mg/cm2, the specific capacitance for LPC-0.5 still remained 146.1 F/g at 0.5 A/g and 102.2 F/g at 50 A/g (70% retention), which successfully indicated the practicability of LPC materials herein (Fig. S8 in Supporting information).

    Figure 3

    Figure 3.  The electrochemical properties of LPC-X (X = 0.3, 0.4 and 0.5) materials in EMIBF4 ILs. (a) CV curves of LPC-Xs measured at 50 mV/s. (b) CV curves of LPC-0.5 under different scan rates ranged from 10 mV/s to 200 mV/s. (c, d) GCD curves of LPC-0.5 tested from 0.5 A/g to 50 A/g. (e) The rate capabilities. (f) EIS spectra. The inset exhibited the equivalent circuit model of EIS.

    The electrochemical impedance spectroscopy (EIS) spectra of LPC-X (X = 0.3, 0.4 and 0.5) were also measured and fitted by equivalent circuit model (Fig. 3f). Obviously, impedance spectra were mainly consisted of three regions: the semicircles at high-frequency region, the 45° slope lines at mid-frequency, and vertical lines in low-frequency. The nearly vertical low-frequency lines represented the ideal capacitive behaviors. At mid-frequency region, the negligible 45° slope lines assigned to Warburg resistance efficiently reflected the fast ion diffusion capability within LPC-Xs electrodes. The distance of the semicircles at the high-frequency, designated the charge transfer resistance (Rct), which was obtained to be 2.42, 1.84 and 1.59 Ω for LPC-0.3, LPC-0.4, and LPC-0.5, respectively. Such small Rct can be attributed to the 3D interconnected porous architecture, high electrical conductivity and appropriate content of dopants, synergistically providing accessible pathways for ion diffusion and electron charge. In addition, the intercept on the real axis at high frequency corresponded to the equivalent series resistance (Rs), which represented the intrinsic resistance of electrode materials, the ionic resistance of electrolyte, and the contact resistance between the electrode and current collector. It can be noticeable that the LPC-0.5 exhibited a slightly higher Rs value than those for LPC-0.3 and LPC-0.4, which can be attributed from the well-developed porous structure restricting the continuous channels of electron diffusion to a certain degree. Nevertheless, the LPC-0.3 and LPC-0.4 exhibits higher O/N heteroatom concentration relative to LPC-0.5, which aggravated the decomposition of electrolyte components, thereby resulting in lower capacitance performances during the high-voltage application [59]. Such observations were in good accordance with the CV and GCD analyses above, collectively confirming the good kinetics and excellent rate capability of LPC-X (X = 0.3, 0.4 and 0.5) electrodes.

    Energy density, power density, as well as the cycling stability are other indicators to probe the practicability of electrode materials in supercapacitors. In this case, symmetrical supercapacitor devices based on the optimal LPC-0.5 (LPC-0.5//LPC-0.5) were assembled as illustrated in Fig. 4a. The Ragone plot qualitatively depicted the relationship between energy density and power density (Fig. 4b), which presented an approximately parallel line to the x-axis with the increased power density, implying its excellent energy-power rating. Furthermore, a maximum energy density of 72 Wh/kg can be reached at the power density of 320 W/kg, and still maintained the high value of 59 Wh/kg even at an ultrahigh power density of 59 kW/kg, which was superior to most of the previous reported lignin derived porous carbon in symmetrical supercapacitors with ionic liquid electrolyte (Table S3 in Supporting information). In addition, it was found in Fig. 4c that the LPC-0.5 sustained an impressive cycling stability with capacitance retention of 93.1% after 10, 000 cycles at 2 A/g. The satisfactory coulombic efficiency of about 98% was obtained and further confirmed the high electrochemical reversibility of the LPC-0.5 electrode. All these results strongly indicated that the LPC-X materials, especially LPC-0.5, can be rendered as high performance promising electrodes for supercapacitors with EMIBF4 IL electrolytes.

    Figure 4

    Figure 4.  (a) Schematic diagram of the assembled supercapacitor device with IL electrolyte. (b) The Ragone plot of LPC-0.5 material. (c) Stability testing conducted at 2 A/g for 10 000 cycles of LPC-0.5 material.

    In summary, lignin-derived porous carbon with rich mesoporisity were designed via a facile template strategy, and validated as efficacious electrode for supercapacitors with IL electrolytes. The as-prepared samples not only exhibited 3D interconnected hierarchical porous scaffold with accessible mesopore, large SSA and favorable pore size distribution, but held high graphitization degree as well as low heteroatom content, cooperatively facilitating the ion and electron kinetics and thus superior electrochemical performance. Benefited from these advantages, the optimal LPC-0.5 sample delivered a high specific capacitance of 166 F/g at the current density of 0.5 A/g with superior rate capability (capacitance retention of 82.5% at 50 A/g) in EMIBF4 electrolyte. Particularly, the symmetric capacitor also reached a high integrated energy-power density of 59 Wh/kg at 59 kW/kg together with excellent cycle stability (93.1% capacitance retention after 10, 000 cycles at 2 A/g). This work provided new insights into designing porous carbon materials from lignin-based raw materials for high-performance supercapacitors with IL electrolytes.

    The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

    This work was supported by the National Natural Science Foundation of China (No. 22209014), Beijing Forestry University Outstanding Young Talent Cultivation Project (No. 2019JQ03017), National Science Fund for Distinguished Young Scholars (No. 32225034), and China-111 Project (No. BP0820033).

    Supplementary material associated with this article can be found, in the online version, at doi:10.1016/j.cclet.2023.108187.


  • 加载中
    1. [1]

      Gregorio F. Ortiz . Some facets of the Mg/Na3VCr0.5Fe0.5(PO4)3 battery. Chinese Chemical Letters, 2024, 35(10): 109391-. doi: 10.1016/j.cclet.2023.109391

    2. [2]

      Shiyi WANGChaolong CHENXiangjian KONGLansun ZHENGLasheng LONG . Polynuclear lanthanide compound [Ce4Ce6(μ3-O)4(μ4-O)4(acac)14(CH3O)6]·2CH3OH for the hydroboration of amides to amine. Chinese Journal of Inorganic Chemistry, 2025, 41(1): 88-96. doi: 10.11862/CJIC.20240342

    3. [3]

      Yanglin Jiang Mingqing Chen Min Liang Yige Yao Yan Zhang Peng Wang Jianping Zhang . Experimental and Theoretical Investigations of Solvent Polarity Effect on ESIPT Mechanism in 4′-N,N-diethylamino-3-hydroxybenzoflavone. Acta Physico-Chimica Sinica, 2025, 41(2): 100012-. doi: 10.3866/PKU.WHXB202309027

    4. [4]

      Hong-Tao JiYu-Han LuYan-Ting LiuYu-Lin HuangJiang-Feng TianFeng LiuYan-Yan ZengHai-Yan YangYong-Hong ZhangWei-Min He . Nd@C3N4-photoredox/chlorine dual catalyzed synthesis and evaluation of antitumor activities of 4-alkylated sulfonyl ketimines. Chinese Chemical Letters, 2025, 36(2): 110568-. doi: 10.1016/j.cclet.2024.110568

    5. [5]

      Yanfen PENGXinyue WANGTianbao LIUXiaoshuo WUYujing WEI . Syntheses and luminescence of four Cd(Ⅱ)/Zn(Ⅱ) complexes constructed by 1,3‐bis(4H‐1,2,4‐triazole)benzene. Chinese Journal of Inorganic Chemistry, 2025, 41(7): 1416-1426. doi: 10.11862/CJIC.20250018

    6. [6]

      Yuwei LiuYihui ZhuWeijian DuanYizhuo YangHaorui TuoChunhua Feng . Electrocatalytic nitrate reduction on Fe, Fe3O4, and Fe@Fe3O4 cathodes: Elucidating structure-sensitive mechanisms of direct electron versus hydrogen atom transfer. Chinese Chemical Letters, 2025, 36(6): 110347-. doi: 10.1016/j.cclet.2024.110347

    7. [7]

      Ruofan YinZhaoxin GuoRui LiuXian-Sen Tao . Ultrafast synthesis of Na3V2(PO4)3 cathode for high performance sodium-ion batteries. Chinese Chemical Letters, 2025, 36(2): 109643-. doi: 10.1016/j.cclet.2024.109643

    8. [8]

      Kai Han Guohui Dong Ishaaq Saeed Tingting Dong Chenyang Xiao . Morphology and photocatalytic tetracycline degradation of g-C3N4 optimized by the coal gangue. Chinese Journal of Structural Chemistry, 2024, 43(2): 100208-100208. doi: 10.1016/j.cjsc.2023.100208

    9. [9]

      Yan ZHAOXiaokang JIANGZhonghui LIJiaxu WANGHengwei ZHOUHai GUO . Preparation and fluorescence properties of Eu3+-doped CaLaGaO4 red-emitting phosphors. Chinese Journal of Inorganic Chemistry, 2024, 40(10): 1861-1868. doi: 10.11862/CJIC.20240242

    10. [10]

      Xuejiao Wang Suiying Dong Kezhen Qi Vadim Popkov Xianglin Xiang . Photocatalytic CO2 Reduction by Modified g-C3N4. Acta Physico-Chimica Sinica, 2024, 40(12): 2408005-. doi: 10.3866/PKU.WHXB202408005

    11. [11]

      Yuan CONGYunhao WANGWanping LIZhicheng ZHANGShuo LIUHuiyuan GUOHongyu YUANZhiping ZHOU . Construction and photocatalytic properties toward rhodamine B of CdS/Fe3O4 heterojunction. Chinese Journal of Inorganic Chemistry, 2024, 40(11): 2241-2249. doi: 10.11862/CJIC.20240219

    12. [12]

      Fei ZHOUXiaolin JIA . Co3O4/TiO2 composite photocatalyst: Preparation and synergistic degradation performance of toluene. Chinese Journal of Inorganic Chemistry, 2024, 40(11): 2232-2240. doi: 10.11862/CJIC.20240236

    13. [13]

      Tian TIANMeng ZHOUJiale WEIYize LIUYifan MOYuhan YEWenzhi JIABin HE . Ru-doped Co3O4/reduced graphene oxide: Preparation and electrocatalytic oxygen evolution property. Chinese Journal of Inorganic Chemistry, 2025, 41(2): 385-394. doi: 10.11862/CJIC.20240298

    14. [14]

      Liang Ma Zhou Li Zhiqiang Jiang Xiaofeng Wu Shixin Chang Sónia A. C. Carabineiro Kangle Lv . Effect of precursors on the structure and photocatalytic performance of g-C3N4 for NO oxidation and CO2 reduction. Chinese Journal of Structural Chemistry, 2024, 43(11): 100416-100416. doi: 10.1016/j.cjsc.2024.100416

    15. [15]

      Yanghanbin Zhang Dongxiao Wen Wei Sun Jiahe Peng Dezhong Yu Xin Li Yang Qu Jizhou Jiang . State-of-the-art evolution of g-C3N4-based photocatalytic applications: A critical review. Chinese Journal of Structural Chemistry, 2024, 43(12): 100469-100469. doi: 10.1016/j.cjsc.2024.100469

    16. [16]

      Qinwen ZhengXin LiuLintao TianYi ZhouLibing LiaoGuocheng Lv . Mechanism of Fenton catalytic degradation of Rhodamine B induced by microwave and Fe3O4. Chinese Chemical Letters, 2025, 36(4): 109771-. doi: 10.1016/j.cclet.2024.109771

    17. [17]

      Yu BAIJijiang WANGLong TANGErlin YUEChao BAIXiao WANGYuqi ZHANG . A cadmium(Ⅱ) coordination polymer based on a semirigid tetracarboxylate ligand for highly selective detection of Fe3+ and 4-nitrophenol. Chinese Journal of Inorganic Chemistry, 2025, 41(6): 1217-1226. doi: 10.11862/CJIC.20240457

    18. [18]

      Yong-Fang Shi Sheng-Hua Zhou Zuju Ma Xin-Tao Wu Hua Lin Qi-Long Zhu . From [Ba3S][GeS4] to [Ba3CO3][MS4] (M = Ge, Sn): Enhancing optical anisotropy in IR birefringent crystals via functional group implantation. Chinese Journal of Structural Chemistry, 2025, 44(1): 100455-100455. doi: 10.1016/j.cjsc.2024.100455

    19. [19]

      Jianyu Qin Yuejiao An Yanfeng ZhangIn Situ Assembled ZnWO4/g-C3N4 S-Scheme Heterojunction with Nitrogen Defect for CO2 Photoreduction. Acta Physico-Chimica Sinica, 2024, 40(12): 2408002-. doi: 10.3866/PKU.WHXB202408002

    20. [20]

      Min WANGDehua XINYaning SHIWenyao ZHUYuanqun ZHANGWei ZHANG . Construction and full-spectrum catalytic performance of multilevel Ag/Bi/nitrogen vacancy g-C3N4/Ti3C2Tx Schottky junction. Chinese Journal of Inorganic Chemistry, 2024, 40(6): 1123-1134. doi: 10.11862/CJIC.20230477

Metrics
  • PDF Downloads(0)
  • Abstract views(763)
  • HTML views(6)

通讯作者: 陈斌, bchen63@163.com
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索
Address:Zhongguancun North First Street 2,100190 Beijing, PR China Tel: +86-010-82449177-888
Powered By info@rhhz.net

/

DownLoad:  Full-Size Img  PowerPoint
Return